ADM242AR
Công ty Analog Devices Inc.
- Lifecycle
- Active
- Stock
- 6746 PCS
- Package
- SOIC-18
- Series
- Interface - Drivers, Receivers, Transceivers
Bảng so sánh chi tiết giữa ADM242AR và ADM241LJR cung cấp những thông tin giá trị về thông số kỹ thuật và các tính năng chính của chúng. Chúng tôi đề cập chi tiết đến các yếu tố quan trọng, bao gồm tuân thủ RoHS, trạng thái REACH, dòng sản phẩm, kiểu lắp đặt, loại bao bì và các đặc điểm liên quan khác. Việc trình bày sự khác biệt cạnh nhau giúp đơn giản hóa việc lựa chọn linh kiện, giúp bạn dễ dàng chọn được tùy chọn tốt nhất cho ứng dụng cụ thể của mình.
Replacement verdict
The ADM241LJR is a functionally compatible candidate for the ADM242AR, sharing the same RS-232 transceiver function, dual driver/receiver channel count, and PDIP-24 package footprint. The primary distinction is the operating temperature range, where the ADM241LJR is specified for the commercial 0°C to 70°C range versus the industrial −40°C to +85°C range of the ADM242AR, so validation is required for industrial-temperature applications.
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADM242AR | ADM241LJR | Why it matters |
|---|---|---|---|
| Number of Drivers/Receivers | 2/2 | 4/0 | Defines the interface direction and channel count; a 2/2 transceiver cannot directly replace a 4/0 driver-only device in a given signal path. |
| Data Rate | 200 kbps | 120 kbps | Maximum supported signaling speed; the lower-rated part may not meet timing requirements of a system designed for the faster device. |
| Receiver Input Impedance | 3 kΩ to 7 kΩ | Not applicable (no receivers) | RS-232 receivers must present the standard 3–7 kΩ load; a driver-only device lacks receivers entirely, changing bus loading behavior. |
| Number of Charge Pump Capacitors | 4 (external) | 4 (external) | External charge-pump capacitors set the on-chip voltage generation; both require the same count, easing board-level substitution of the power section. |
| Operating Supply Voltage | 5 V | 5 V | Both operate from a single 5 V rail, so the power supply architecture is compatible between the two parts. |
| Shutdown / Enable Feature | Yes (active-low shutdown) | Yes (active-low shutdown) | Shutdown capability allows power savings; matching behavior means firmware and control-line logic remain compatible. |
| Package | 20-lead SOIC (wide) | 20-lead SOIC (wide) | Identical package and pin count allow the same PCB footprint, though pin functions differ due to driver/receiver configuration. |
| Operating Temperature Range | -40 °C to +85 °C | 0 °C to +70 °C | The wider industrial range of the ADM242AR supports harsher environments; the commercial-range part may not be suitable for extended-temperature applications. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | ADM242AR | ADM241LJR |
|---|---|---|
| Supplier | - | Analog Devices Inc.,Rochester Electronics, LLC |
| Part Status | Obsolete | Obsolete |
| Type | Transceiver | Transceiver |
| Protocol | RS232 | RS232 |
| Number of Drivers/Receivers | 2/2 | 4/5 |
| Duplex | Full | Full |
| Receiver Hysteresis | 400 mV | 650 mV |
| Data Rate | 200kbps | 120Kbps |
| Voltage - Supply | 4.5V ~ 5.5V | 4.75V ~ 5.25V |
| Operating Temperature | -40°C ~ 85°C | 0°C ~ 70°C |
| Mounting Type | Surface Mount | Surface Mount |
The ADM242AR is a dual-channel RS-232 line driver/receiver in a 20-lead SOIC package, while the ADM241LJR is a single-channel RS-232 transceiver in a 24-lead SOIC package. The ADM242AR integrates two drivers and two receivers, whereas the ADM241LJR integrates one driver and one receiver. Both operate from a single +5 V supply and include on-chip charge pump circuitry.
No. The ADM242AR uses a 20-lead SOIC package and the ADM241LJR uses a 24-lead SOIC package, so they have different pin counts and pinouts. They are not direct drop-in replacements for each other.
Both devices operate from a single +5 V supply. On-chip charge pump converters generate the required RS-232 voltage levels from this single supply.
The ADM242AR provides two RS-232 drivers and two RS-232 receivers. The ADM241LJR provides one RS-232 driver and one RS-232 receiver.
Yes. Both the ADM242AR and ADM241LJR include a shutdown mode that reduces power consumption when the RS-232 interface is inactive. The shutdown feature is controlled via a dedicated logic input pin.
Both devices are specified for RS-232 data rates up to 120 kbps, which is sufficient for standard RS-232 communication requirements.
No. Both devices are specified for +5 V single-supply operation. They are not rated for 3.3 V or other low-voltage supply rails. For 3 V RS-232 applications, a different device family should be selected.
Both devices are specified for the commercial temperature range of 0°C to +70°C. They are not rated for industrial or extended temperature operation.