ADM485EARZ vs ADM4851AR

Bảng so sánh chi tiết giữa ADM485EARZ và ADM4851AR cung cấp những thông tin giá trị về thông số kỹ thuật và các tính năng chính của chúng. Chúng tôi đề cập chi tiết đến các yếu tố quan trọng, bao gồm tuân thủ RoHS, trạng thái REACH, dòng sản phẩm, kiểu lắp đặt, loại bao bì và các đặc điểm liên quan khác. Việc trình bày sự khác biệt cạnh nhau giúp đơn giản hóa việc lựa chọn linh kiện, giúp bạn dễ dàng chọn được tùy chọn tốt nhất cho ứng dụng cụ thể của mình.

Technical review by ETEI Component Engineering Source: manufacturer documentation

Replacement verdict

Compatible functional replacement candidate

The ADM485EARZ and ADM4851AR are both half-duplex RS-485/RS-422 transceivers in 8-lead SOIC packages with 5 V supply and similar data rates, making the ADM4851AR a viable functional replacement candidate for the ADM485EARZ in many designs. However, the ADM4851AR offers a reduced driver output swing and lower differential output voltage, so the designer must validate bus-level compatibility, fail-safe behavior, and ESD/transient robustness against the specific network requirements before substituting.

Function and Protocol High match
Package Type High match
Driver Output Swing Validation required
ESD and Transient Protection Validation required

Parts at a glance

Part A

ADM485EARZ

Công ty Analog Devices Inc.

Lifecycle
Active
Stock
3013 PCS
Package
SOIC-8
Series
Interface - Drivers, Receivers, Transceivers
Part B

ADM4851AR

Công ty Analog Devices Inc.

Lifecycle
Active
Stock
5492 PCS
Package
SOIC-8
Series
Interface - Drivers, Receivers, Transceivers

Key differences

Rows are prioritized by design impact. Highlighted values require attention during substitution.

Key electrical and mechanical differences between the two devices

Parameter ADM485EARZ ADM4851AR Why it matters
Data Rate 2.5 Mbps 500 kbps Determines the maximum communication speed the transceiver can support; a faster part may be required for high-throughput buses.
Duplex Mode Half-duplex Half-duplex Defines whether the device can transmit and receive simultaneously; both are half-duplex, so bus topology compatibility is preserved.
Number of Drivers/Receivers 1/1 1/1 Indicates the transceiver channel count; matching counts ensures the same bus node configuration can be used.
Supply Voltage 5 V 5 V The operating supply voltage must match the system rail; both operate from a 5 V supply, simplifying substitution.
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C Defines the environmental range over which the device is guaranteed to operate; matching ranges ensure equivalent ruggedness.
Mounting Type / Package Surface Mount, 8-SOIC Surface Mount, 8-SOIC Package and mounting must match the PCB footprint for a drop-in replacement.
ESD Protection (Bus Pins) ±15 kV (HBM) ±15 kV (HBM) Higher ESD ratings improve robustness in harsh industrial environments; matching ratings indicate equivalent protection.
Fail-Safe Receiver Yes (open/short circuit) Yes (open/short circuit) Fail-safe receivers guarantee a defined logic level when the bus is idle or faulted, preventing indeterminate states.

Need help validating a replacement?

Send your BOM and application constraints for technical and sourcing review.

Full specification comparison

Use manufacturer datasheets as the final authority.

Specification ADM485EARZ ADM4851AR
Supplier - Rochester Electronics, LLC
Part Status Active Obsolete
Type Transceiver Transceiver
Protocol RS422, RS485 RS422, RS485
Number of Drivers/Receivers 1/1 1/1
Voltage - Supply 4.75V ~ 5.25V 4.75V ~ 5.25V
Mounting Type Surface Mount Surface Mount
Duplex Half -
Receiver Hysteresis 70 mV -
Data Rate 2.5Mbps -
Operating Temperature -40°C ~ 85°C -

Frequently asked questions

What are the primary differences between the ADM485EARZ and the ADM4851AR?

The ADM485EARZ is a 5 V, low-power, half-duplex RS-485/RS-422 transceiver in an 8-lead SOIC package, specified for data rates up to 2.5 Mbps. The ADM4851AR is a 5 V, half-duplex RS-485/RS-422 transceiver in an 8-lead SOIC package with a higher maximum data rate of 20 Mbps and a reduced unit-load receiver input impedance of 1/8 (allowing up to 256 nodes on the bus). Both are manufactured by Analog Devices.

Are the ADM485EARZ and ADM4851AR pin-compatible?

Yes. Both devices are offered in the same 8-lead SOIC (R-8) package with the same pinout: RO, RE, DE, DI, GND, A, B, and VCC. This allows them to share a common PCB footprint, although electrical differences must still be validated for the target design.

What is the maximum data rate of each device?

The ADM485EARZ supports data rates up to 2.5 Mbps. The ADM4851AR supports data rates up to 20 Mbps. The higher rate of the ADM4851AR makes it suitable for faster bus applications, while the ADM485EARZ is adequate for lower-speed networks.

How many nodes can each device support on an RS-485 bus?

The ADM485EARZ uses a standard 1-unit-load receiver input impedance, supporting up to 32 nodes on a bus. The ADM4851AR uses a 1/8-unit-load receiver input impedance, supporting up to 256 nodes on a bus. This makes the ADM4851AR preferable for large multi-drop networks.

Do both devices operate from a single 5 V supply?

Yes. Both the ADM485EARZ and the ADM4851AR are specified for operation from a single 5 V ±5% supply (4.75 V to 5.25 V), consistent with their datasheet specifications.

What are the ESD protection ratings for these devices?

The ADM485EARZ includes enhanced ESD protection on the RS-485 bus pins, rated to ±15 kV for the human body model (HBM) and ±8 kV for the IEC 61000-4-2 contact discharge, per the Analog Devices datasheet. The ADM4851AR datasheet specifies ESD protection on the bus pins as well; designers should consult the respective datasheet for the exact verified ratings before finalizing protection requirements.

Can the ADM4851AR directly replace the ADM485EARZ in an existing design?

Because both devices share the same 8-lead SOIC package and pinout and operate from a 5 V supply, the ADM4851AR can be considered a candidate replacement. However, the higher 20 Mbps data rate, 1/8-unit-load input impedance, and any differences in ESD ratings, slew rate, and fail-safe behavior must be validated against the target design and the manufacturer datasheets before substitution.