AMC1300BDWVR vs AMC1311BDWVR

Bảng so sánh chi tiết giữa AMC1300BDWVR và AMC1311BDWVR cung cấp những thông tin giá trị về thông số kỹ thuật và các tính năng chính của chúng. Chúng tôi đề cập chi tiết đến các yếu tố quan trọng, bao gồm tuân thủ RoHS, trạng thái REACH, dòng sản phẩm, kiểu lắp đặt, loại bao bì và các đặc điểm liên quan khác. Việc trình bày sự khác biệt cạnh nhau giúp đơn giản hóa việc lựa chọn linh kiện, giúp bạn dễ dàng chọn được tùy chọn tốt nhất cho ứng dụng cụ thể của mình.

Technical review by ETEI Component Engineering Source: manufacturer documentation

Replacement verdict

Compatible functional replacement candidate

The AMC1311BDWVR and AMC1300BDWVR are both isolated amplifiers in the same SOIC-8 (DWV) package with matching pinout and 5.0 kV reinforced isolation ratings, making them strong functional replacement candidates. However, they differ in input voltage range and gain architecture: the AMC1311B is a high-impedance ±1 V input voltage-sensing amplifier, while the AMC1300B is a ±250 mV shunt-current-sensing amplifier with fixed gain. Designers must validate that the input signal range, gain, and output offset match the target application before substituting one for the other.

Package and Pinout High match
Isolation Rating High match
Input Voltage Range Validation required
Gain and Output Configuration Not compatible

Parts at a glance

Part A

AMC1300BDWVR

Texas Dụng cụ

Lifecycle
Active
Stock
1306 PCS
Package
SOIC-8
Series
Linear - Amplifiers - Special Purpose
Part B

AMC1311BDWVR

Texas Dụng cụ

Lifecycle
Active
Stock
3122 PCS
Package
SOIC-8
Series
Linear - Amplifiers - Special Purpose

Key differences

Rows are prioritized by design impact. Highlighted values require attention during substitution.

Key electrical and mechanical differences between the two devices

Parameter AMC1311BDWVR AMC1300BDWVR Why it matters
Input Signal Type Voltage input (high-impedance, ±1 V range) Current shunt input (low-impedance, ±250 mV range) Determines whether the device senses a voltage directly or a shunt resistor voltage drop; these are not functionally interchangeable for the same sensing topology.
Input Voltage Range ±1 V (nominal, high impedance) ±250 mV (nominal, low impedance) The full-scale input range must match the sensed signal amplitude; a mismatch causes clipping or poor resolution.
Input Impedance High impedance (voltage-sense optimized) Low impedance (shunt-sense optimized) Affects loading on the measured node and suitability for voltage vs. shunt-current sensing applications.
Isolation Rating 5 kV RMS (reinforced isolation) 5 kV RMS (reinforced isolation) Both provide equivalent reinforced galvanic isolation, so safety/isolation performance is comparable.
Output Interface Differential analog output Differential analog output Both present a differential analog output suitable for feeding a delta-sigma modulator or differential ADC front end.
Supply Voltage 3.0 V to 5.5 V (both sides) 3.0 V to 5.5 V (both sides) Identical supply requirements simplify power-rail design and allow drop-in compatibility on the supply side.
Package 8-pin SOIC (DW, wide body) 8-pin SOIC (DW, wide body) Same package and pinout enable PCB footprint compatibility, though electrical function still differs.
Typical Application Isolated voltage sensing (e.g., DC-link/bus voltage) Isolated current sensing via shunt resistor The intended measurement target differs, so substitution requires matching the sensing function, not just the package.

Need help validating a replacement?

Send your BOM and application constraints for technical and sourcing review.

Full specification comparison

Use manufacturer datasheets as the final authority.

Specification AMC1300BDWVR AMC1311BDWVR
Part Status Active Active
Type Isolation Isolation
Applications Current Sensing, Power Management -
Mounting Type Surface Mount Surface Mount

Frequently asked questions

What are the primary functional differences between the AMC1311BDWVR and AMC1300BDWVR?

The AMC1311BDWVR is a precision isolated amplifier designed for voltage sensing with a high input impedance of 1 GΩ and a ±1 V input range, while the AMC1300BDWVR is an isolated amplifier optimized for current sensing via a shunt resistor with a ±250 mV input range and a fixed gain of 8. Both are reinforced isolated amplifiers in the same SOIC-8 (DWV) package, but they differ in input range, input impedance, and intended sensing application.

Are the AMC1311BDWVR and AMC1300BDWVR pin-compatible?

Yes. Both devices are offered in the same 8-pin SOIC (DWV) package with the same pinout: VDD1, INP, INN, GND1 on the primary side and VDD2, OUTP, OUTN, GND2 on the secondary side. This allows a common PCB footprint, but electrical differences must still be validated before substitution.

What are the input voltage ranges of the AMC1311BDWVR and AMC1300BDWVR?

The AMC1311BDWVR has a specified input voltage range of ±1 V with a nominal gain of 1, intended for direct voltage sensing. The AMC1300BDWVR has a specified input voltage range of ±250 mV with a fixed gain of 8, intended for shunt-resistor current sensing. The input ranges are not interchangeable without adjusting the sensing front end.

Do both devices provide reinforced isolation?

Yes. Both the AMC1311BDWVR and AMC1300BDWVR are reinforced isolated amplifiers rated for a maximum isolation working voltage of 1500 V RMS per the manufacturer datasheet, with isolation ratings suitable for high-voltage industrial measurement applications. Designers should still confirm the specific isolation parameters required by their end application against the datasheet.

Can the AMC1311BDWVR directly replace the AMC1300BDWVR in a current-sensing circuit?

No, not directly. The AMC1300BDWVR is designed for ±250 mV shunt-resistor inputs with a gain of 8, whereas the AMC1311BDWVR has a ±1 V input range and unity gain. A direct replacement would change the signal scaling and may exceed the input range of the AMC1311BDWVR depending on the shunt voltage, so the sensing network and signal chain must be redesigned and validated.

What are the supply voltage requirements for the AMC1311BDWVR and AMC1300BDWVR?

Both devices operate with a primary-side supply (VDD1) of 3.0 V to 5.5 V and a secondary-side supply (VDD2) of 3.0 V to 5.5 V, per the manufacturer datasheet. The isolated dual-supply architecture allows the high-voltage and low-voltage sides to be powered independently.

What are the typical applications for each device?

The AMC1311BDWVR is typically used for isolated voltage sensing, such as DC-link voltage monitoring in motor drives and inverter systems, due to its high input impedance and ±1 V range. The AMC1300BDWVR is typically used for isolated current sensing with shunt resistors in motor control, power inverters, and industrial measurement systems, due to its ±250 mV range and gain of 8.

Do both devices share the same operating temperature range?

Yes. Both the AMC1311BDWVR and AMC1300BDWVR are specified for an operating temperature range of –40°C to +125°C per the manufacturer datasheet, making them suitable for industrial environments. Designers should verify thermal performance in their specific application conditions.